Engine Inventor File |
Post Reply |
Author | |
hpiracer21z
Bolt Sorter Joined: Jul/25/2009 Location: Gary, IN Status: Offline Points: 9 |
Post Options
Thanks(0)
Posted: Aug/04/2009 at 11:07pm |
Does anyone happen to have an inventor model of the Briggs engine. It would be greatly appreciated.
Thanks |
|
Mike
Purdue University Calumet |
|
adrive7
Baja Godfather Joined: Oct/19/2008 Location: Lancaster, CA Status: Offline Points: 711 |
Post Options
Thanks(0)
|
-Joe
Chief Organizer, Baja California 2016, 2017, 2019 Ohio State Baja 2005-2009 Co-Host, Science... Sort Of http://www.sciencesortof.com |
|
hpiracer21z
Bolt Sorter Joined: Jul/25/2009 Location: Gary, IN Status: Offline Points: 9 |
Post Options
Thanks(0)
|
Thank you, you just saved me so much modeling time.
|
|
Mike
Purdue University Calumet |
|
rjwoods77
Milling Master Joined: Jul/05/2009 Status: Offline Points: 65 |
Post Options
Thanks(0)
|
Is that the iges surface model that has been around for a while?
|
|
adrive7
Baja Godfather Joined: Oct/19/2008 Location: Lancaster, CA Status: Offline Points: 711 |
Post Options
Thanks(0)
|
No Problem. It's kind of a goofy model to deal with, but its accurate. (should be, it's from B&S)
rj: Yes, it is. I put it on 3DContentCentral so it can be downloaded in many formats. Edited by adrive7 - Aug/05/2009 at 3:42pm |
|
-Joe
Chief Organizer, Baja California 2016, 2017, 2019 Ohio State Baja 2005-2009 Co-Host, Science... Sort Of http://www.sciencesortof.com |
|
TerpsRacing-Dan
Bolt Sorter Joined: Oct/23/2008 Location: Baltimore, MD Status: Offline Points: 27 |
Post Options
Thanks(0)
|
I always meant to take that engine and simplify it, cut out everything but external surfaces, that thing slowed down our model really badly. I usually kept it on a separate layer and turned it off unless i needed it.
|
|
iwm
Bolt Sorter Joined: Jul/09/2009 Status: Offline Points: 23 |
Post Options
Thanks(0)
|
Has anyone else found that the bolt pattern on the bottom of the engine used for mounting is not accurate in the CAD model? We have had engine mounting issues for a few years and finally tracked it down to being an issue with the CAD model.
|
|
Unproductive
Milling Master Joined: Jul/11/2009 Location: Rochester NY Status: Offline Points: 66 |
Post Options
Thanks(0)
|
What kind of mounting problems did you have? Our clutch center to center was off by ~.060, but we're pretty sure it was a manufacturing error on our part, things like that happen pretty easily when you have to rush.
|
|
-Bob
|
|
adrive7
Baja Godfather Joined: Oct/19/2008 Location: Lancaster, CA Status: Offline Points: 711 |
Post Options
Thanks(0)
|
I've milled the engine mount holes dimensioned exactly as modeled. Bolts dropped right in. |
|
-Joe
Chief Organizer, Baja California 2016, 2017, 2019 Ohio State Baja 2005-2009 Co-Host, Science... Sort Of http://www.sciencesortof.com |
|
JumpBuggie
Bolt Sorter Joined: Nov/24/2013 Status: Offline Points: 3 |
Post Options
Thanks(0)
|
shivam chaubey
Double Secret Probation Banned Joined: Mar/05/2014 Location: Silchar Status: Offline Points: 6 |
Post Options
Thanks(0)
|
What is the exact center of mass location for b&s 1450..?
|
|
Pedro UFPBaja
Baja Godfather Joined: Mar/03/2010 Location: Brazil Status: Offline Points: 886 |
Post Options
Thanks(0)
|
Dude, you just asked the same question on another topic, got answers but even so you spammed the forums?
|
|
Former Team Captain
|
|
mchlfranko
Bolt Sorter Joined: Jul/10/2014 Location: Waterloo, ON Status: Offline Points: 24 |
Post Options
Thanks(0)
|
How accurate is the model that Jump Buggie posted? Anyone seen any discrepancies?
|
|
RLM
Baja Godfather Joined: Nov/15/2012 Location: Hamilton, ON Status: Offline Points: 1258 |
Post Options
Thanks(1)
|
Between the New engine we received this past year, the muffler is a bit different and the air filter housing is different. other than that, nothing that I can see.
|
|
McMaster Baja Racing (09-Dec 2015)
Team Captain 2012-2015 Suspension Lead 2015-2016 All spoonfeed PM requests will be billed at $10 USD per reply, payable via paypal. |
|
collinskl1
Baja Godfather Joined: Jan/21/2009 Location: Saginaw, MI Status: Offline Points: 1056 |
Post Options
Thanks(0)
|
It would be really cool for someone to see if a place would laser scan an engine as a sponsorship activity for all teams...
|
|
Kyle Collins
Lipscomb University Alumni 2x Project Manager Nexteer Automotive Product Engineer, Electronic Power Steering ... and the 8th simple machine: a bigger hammer. |
|
rasmuet
Welding Master Joined: Apr/29/2013 Location: Ann Arbor, MI Status: Offline Points: 310 |
Post Options
Thanks(0)
|
I think we were looking into having a place do that for us. If we end up doing so I can see about sharing the model.
|
|
Erik
Iowa State Baja 2011-Dec 2014 Drivetrain Design 2013, 2014, 2015 2014 Kansas - Car #45 - 1st Place Endurance |
|
Rollie
Welding Master Joined: Nov/07/2012 Location: FH, MI Status: Offline Points: 133 |
Post Options
Thanks(0)
|
We just had the newer model motor white light scanned. I'm filling in the holes now but so far this is what we have. I will share with everyone when I finish it.
|
|
Zac Watts
2013-2015 Kettering University 2016-* KU Industry Advisor Team Captain Design Engineer at Pratt & Miller Engineering |
|
mchlfranko
Bolt Sorter Joined: Jul/10/2014 Location: Waterloo, ON Status: Offline Points: 24 |
Post Options
Thanks(0)
|
So awesome!
|
|
Nate
Welding Master Joined: Jun/16/2014 Location: Ames, IA Status: Offline Points: 285 |
Post Options
Thanks(0)
|
Rollie,
Do you think you could do one with the gas tank off? We might do a laser scanned model this year and post it too, but your white light scanned model looks great. |
|
Iowa State University Cyclone Racing 2013 - 2016
Tech Director, DAQ, Media, Manufacturing, Radios 2016 - S&T, Maneuv, & Endurance Driver "Because BAJA" "Because RACECAR" |
|
Rollie
Welding Master Joined: Nov/07/2012 Location: FH, MI Status: Offline Points: 133 |
Post Options
Thanks(2)
|
I don't think I'll be able to get this scanned again but when I finish up the model I'll make a second one with that part missing. It will be simple geometry but fairly accurate.
|
|
Zac Watts
2013-2015 Kettering University 2016-* KU Industry Advisor Team Captain Design Engineer at Pratt & Miller Engineering |
|
Rollie
Welding Master Joined: Nov/07/2012 Location: FH, MI Status: Offline Points: 133 |
Post Options
Thanks(2)
|
I have gone through our model to fill in as many holes as possible. I have added in all of the critical bolt geometry and reference planes so that it is a usable model. Some of the hole filling caused some of the parts to combine, like under the gas tank and hoses, but all of the critical geometry and the outer profile are correct. As of now I don't have a model of the motor without the gas tank but you should be able to cut that out of the model.
|
|
Zac Watts
2013-2015 Kettering University 2016-* KU Industry Advisor Team Captain Design Engineer at Pratt & Miller Engineering |
|
Pedro UFPBaja
Baja Godfather Joined: Mar/03/2010 Location: Brazil Status: Offline Points: 886 |
Post Options
Thanks(0)
|
Very nice, that's a great contribution for baja SAE teams around the world
|
|
Former Team Captain
|
|
Rollie
Welding Master Joined: Nov/07/2012 Location: FH, MI Status: Offline Points: 133 |
Post Options
Thanks(0)
|
Glad I could help
|
|
Zac Watts
2013-2015 Kettering University 2016-* KU Industry Advisor Team Captain Design Engineer at Pratt & Miller Engineering |
|
Richie_Dagger
Baja Godfather Joined: Sep/25/2011 Location: Las Vegas, NV Status: Offline Points: 615 |
Post Options
Thanks(0)
|
How do you open it in SolidWorks? I tried and it's blank.
|
|
Rollie
Welding Master Joined: Nov/07/2012 Location: FH, MI Status: Offline Points: 133 |
Post Options
Thanks(0)
|
I am not sure how to do it in Solidworks. I will try opening it in inventor and saving it as a different file type for you.
|
|
Zac Watts
2013-2015 Kettering University 2016-* KU Industry Advisor Team Captain Design Engineer at Pratt & Miller Engineering |
|
zglazer
Baja Godfather Joined: May/27/2012 Location: Metro Detroit Status: Offline Points: 593 |
Post Options
Thanks(0)
|
If you export it as a parasolid or STEP, it should work with just about anything.
|
|
Zack Glazer
McGill Baja Racing Alumnus 2009-2013 http://baja.mcgilleus.ca/ 2012-2013 Drivetrain Designer |
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |